MCC5B is a 6 pole, 5 x luminaire output single channel device with PIR presence Connection or 3 pole absence connection.

Our Scene set control plates are used with our plug in and addressable control modules to permit the control of different lighting groups at different levels. From the plate you can call Scenes 1-4, Raise, Lower and Off. The Off button can also be programmed to a scene value. You press and hold buttons 1-4 to call scene 5-8.

Functions are identical on the Architrave Plate except that there are 2 fewer buttons. Control plates have blue LED back lighting for location and scene identification, and scenes are programmed via hand-held programmer, wirelessly via Bluetooth from a PC, or by using the buttons (eliminating the need for specialist equipment).

Connection to the system is by 4-core cable with a push on male plug to the scene set plate and a RJ12 connector to the LCM.

MCC10B is a new version of an existing product. With 10 x 6-pole luminaire outputs. Dual channel with 2 x 6-pole presence connection 2 x 6 + 3-pole absence connection its simple to install and offers a cost effective solution for luminaire connections.

Our MCC Connection Centre and MDCC standalone addressable LCM, can be connected using the same leads. They are supplied with a 6-pole side latching plug, to a free end using 1.00mm² LS0H cable.

This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/blue industry standard, connector coding.

Alternatively there is an option for black/grey connectors.

Our Metway fully addressable leads are supplied with a 6-pole side latching plug, to a free end using 1.00mm² LS0H cable. This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/blue industry standard, connector coding. These leads will connect to the two fully addressable lcm's MA-DD1LCM10/M and also MA-DS10LCM10-S5.

The Metway DALI gateway provides an interface between DALI lighting products and our addressable control system. The module acts as a fully functional DALI addressable product with 64 individually programmable addresses. Each address can be a DALI luminaire, emergency inverter, PIR sensor, controlled relay or scene set plate.

The DALI64 is DIN rail mounted and enclosed in a steel powder coated enclosure wired to industry standard terminals.

Twin DALI64 units (i.e with 128 addresses) is also available.

A removeable memory module facilitates fast configuration of a replacement gateway should that be needed. In other words, should an gateway need to be replaced for any reason, no reprogramming is necessary, simply remove the memory module and reinsert it into the new controller.

Our classic latching lead, can be used in a variety of LCM's (For example: Phillips Dynalite). They are supplied with a 6-pole centre latching plug, to a free end using 1.00mm² LS0H cable. This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/blue industry standard, connector coding. Alternatively there is an option for black/grey connectors.

Our classic non-latching box lead, can be used in a variety of LCM's (For example: Delmatic, Ex-Or). They are supplied with a 6-pole centre latching plug, to a free end using 1.00mm² LS0H cable. This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/grey industry standard, connector coding. Alternatively there is an option for black/blue connectors.

Metway can provide leads for other manufacturers lcms, such as Ensto.

The LCM lead is supplied with a 6-pole latching plug, to a free end on 1.00mm² LS0H cable.

This can be supplied in a variety of cores, and length as per your requirements.

These are provided with a blue/white industry standard connector coding.

Metway can provide leads for other manufacturers lcms, such as Ex-Or.

The LCM lead is supplied with a 6-pole latching plug, to a free end on 1.00mm² LS0H cable.

This can be supplied in a variety of cores, and length as per your requirements.

These are provided with a black/grey industry standard connector coding.

Metway can provide leads for other manufacturers lcms, such as CP Electronics.

The LCM lead is supplied with a 6-pole latching plug, to a free end on 1.00mm² LS0H cable.

This can be supplied in a variety of cores, and length as per your requirements.

These are provided with a black/blue industry standard connector coding.

Metway can provide leads for other manufacturers lcms, such as Hager Klik.

The LCM lead is supplied with a 6-pole latching plug, to a free end on 1.00mm² LS0H cable.

This can be supplied in a variety of cores, and length as per your requirements.