MCC5B is a 6 pole, 5 x luminaire output single channel device with PIR presence Connection or 3 pole absence connection.

MCC10B is a new version of an existing product. With 10 x 6-pole luminaire outputs. Dual channel with 2 x 6-pole presence connection 2 x 6 + 3-pole absence connection its simple to install and offers a cost effective solution for luminaire connections.

The MSBS is a 360° switching high-bay sensor, that can be mounted to a batten type luminaire. There is a daylight sensor built-in, the sensor is programmed using the remote controller MPROG.

Our MCC Connection Centre and MDCC standalone addressable LCM, can be connected using the same leads. They are supplied with a 6-pole side latching plug, to a free end using 1.00mm² LS0H cable.

This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/blue industry standard, connector coding.

Alternatively there is an option for black/grey connectors.

The PIRDA is a 360° dimming PIR sensor.

Designed with a low profile for aesthetically demanding architectural projects providing a high quality sensor for simple on / off occupancy control or providing semi-automatic (absence detection) control.

An intelligent photocell is also included to prevent switching of the lights when natural daylight is available.

Set-up of the sensor is carried out using a remote control handset with program memory allowing one-key commissioning where common settings are used for multiple devices.

The MWDD is a 360° dimming microwave sensor.

Designed with a low profile for aesthetically demanding architectural projects providing a high quality sensor for simple on / off occupancy control or providing semi-automatic (absence detection) control.

An intelligent photocell is also included to prevent switching of the lights when natural daylight is available.

Set-up of the sensor is carried out using a remote control handset with program memory allowing one-key commissioning where common settings are used for multiple devices.

The MDABS is a 360° DALI high-bay sensor, that can be mounted to a batten type luminaire. There is a daylight sensor built-in, the sensor is programmed using the remote controller MPROG.

Our Metway fully addressable leads are supplied with a 6-pole side latching plug, to a free end using 1.00mm² LS0H cable. This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/blue industry standard, connector coding. These leads will connect to the two fully addressable lcm's MA-DD1LCM10/M and also MA-DS10LCM10-S5.

Our MDSS7S SmartSensor has been developed to provide a cost effective DALI sensor with a wide range of functions, coupled with a high level of performance.

Housed in a compact moulded enclosure, SmartSensor can operate as part of a managed DALI lighting network, or function as a versatile stand-alone sensor with extensive control capability.

As a stand-alone sensor, the unit is configured using a simple, user-friendly infra-red remote control, with coloured LEDs on the sensor providing feedback for all commands.

As part of a networked system, the sensor settings are managed by a DALI area controller.

The Metway DALI gateway provides an interface between DALI lighting products and our addressable control system. The module acts as a fully functional DALI addressable product with 64 individually programmable addresses. Each address can be a DALI luminaire, emergency inverter, PIR sensor, controlled relay or scene set plate.

The DALI64 is DIN rail mounted and enclosed in a steel powder coated enclosure wired to industry standard terminals.

Twin DALI64 units (i.e with 128 addresses) is also available.

A removeable memory module facilitates fast configuration of a replacement gateway should that be needed. In other words, should an gateway need to be replaced for any reason, no reprogramming is necessary, simply remove the memory module and reinsert it into the new controller.

The Metway MA-CANPIR passive infra red detector is an addressable sensor for use with the MA addressable range of LCM's and gateways. It detects movement using a PIR sensor, which updates the light controller using a CAN bus interface.

Daylight linking can be configured either to keep lights off when there is sufficient ambient light, or used as part of a closed loop to maintain a pre-set luminance level in a dimmable system.

Connection is made by RJ12 connectors on the back of the unit, there are two of these to allow easy onward connection.

Our classic latching lead, can be used in a variety of LCM's (For example: Phillips Dynalite). They are supplied with a 6-pole centre latching plug, to a free end using 1.00mm² LS0H cable. This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/blue industry standard, connector coding. Alternatively there is an option for black/grey connectors.