MCC5B is a 6 pole, 5 x luminaire output single channel device with PIR presence Connection or 3 pole absence connection.

Our Scene set control plates are used with our plug in and addressable control modules to permit the control of different lighting groups at different levels. From the plate you can call Scenes 1-4, Raise, Lower and Off. The Off button can also be programmed to a scene value. You press and hold buttons 1-4 to call scene 5-8.

Functions are identical on the Architrave Plate except that there are 2 fewer buttons. Control plates have blue LED back lighting for location and scene identification, and scenes are programmed via hand-held programmer, wirelessly via Bluetooth from a PC, or by using the buttons (eliminating the need for specialist equipment).

Connection to the system is by 4-core cable with a push on male plug to the scene set plate and a RJ12 connector to the LCM.

The PIRSW is a 360° switching PIR sensor. Designed with a low profile for aesthetically demanding architectural projects providing a high quality sensor for simple on / off occupancy control or providing semi-automatic (absence detection) control.

An intelligent photocell is also included to prevent switching of the lights when natural daylight is available Set-up of the sensor is carried out using a remote control handset with program memory allowing one-key commissioning where common settings are used for multiple devices.

The MPROG is a compact infrared handset used for the basic programming of IR enabled Metway products.

Pointing the handset

You must point the handset directly at the device that you want to control or program. When programming a device it is only necessary to point the handset when ‘sending’ a new setting.

Sending settings to a device

To send the programming parameters to the device, it is simply a case of pressing the relevant button for the setting you require. If the setting is in red type, you would press the 'Shift' button (this handset will display a red light to denote this) and then press the setting you require.

MCC10B is a new version of an existing product. With 10 x 6-pole luminaire outputs. Dual channel with 2 x 6-pole presence connection 2 x 6 + 3-pole absence connection its simple to install and offers a cost effective solution for luminaire connections.

The MMSW is a 360° switching microwave sensor. Designed with a low profile for aesthetically demanding architectural projects providing a high quality sensor for simple on / off occupancy control or providing semi-automatic (absence detection) control.

An intelligent photocell is also included to prevent switching of the lights when natural daylight is available. Set-up of the sensor is carried out using a remote control handset with program memory allowing one-key commissioning where common settings are used for multiple devices.

The SmartSensor Remote Control (MDSSR) provides a simple, low cost method to configure the SmartSensor range of DALI multisensors. It can also allow a user to remote control lighting managed by SmartSensor.

Compact and easy to use, MDSSR is smaller than a credit card and slips easily into the pocket.

Supplied in a plastic pouch with a Lithium coin battery and Programming Guide.

The MSBS is a 360° switching high-bay sensor, that can be mounted to a batten type luminaire. There is a daylight sensor built-in, the sensor is programmed using the remote controller MPROG.

The PIRDA is a 360° dimming PIR sensor.

Designed with a low profile for aesthetically demanding architectural projects providing a high quality sensor for simple on / off occupancy control or providing semi-automatic (absence detection) control.

An intelligent photocell is also included to prevent switching of the lights when natural daylight is available.

Set-up of the sensor is carried out using a remote control handset with program memory allowing one-key commissioning where common settings are used for multiple devices.

The MWDD is a 360° dimming microwave sensor.

Designed with a low profile for aesthetically demanding architectural projects providing a high quality sensor for simple on / off occupancy control or providing semi-automatic (absence detection) control.

An intelligent photocell is also included to prevent switching of the lights when natural daylight is available.

Set-up of the sensor is carried out using a remote control handset with program memory allowing one-key commissioning where common settings are used for multiple devices.

The MDABS is a 360° DALI high-bay sensor, that can be mounted to a batten type luminaire. There is a daylight sensor built-in, the sensor is programmed using the remote controller MPROG.

Our MDSS7S SmartSensor has been developed to provide a cost effective DALI sensor with a wide range of functions, coupled with a high level of performance.

Housed in a compact moulded enclosure, SmartSensor can operate as part of a managed DALI lighting network, or function as a versatile stand-alone sensor with extensive control capability.

As a stand-alone sensor, the unit is configured using a simple, user-friendly infra-red remote control, with coloured LEDs on the sensor providing feedback for all commands.

As part of a networked system, the sensor settings are managed by a DALI area controller.